ADSBexchange.com
Custom Image - System Info

(..back to main menu)

Feeder Name
Public IP
 
lo5

207.66.71.150

Local IP: 
192.168.1.155

Configured Location: 
Macedon
US-NY
United States of America (the)

Zerotier Status: 
zerotier is disabled.

Uptime: 
Current Time: Mon May 11 04:31:26 UTC 2026
Uptime: up 5 minutes
Since 2026-05-11 04:26:20

Voltage Drops: 
Status: 0x0
Undervolted:
   Now: NO
   Run: NO
Throttled:
   Now: NO
   Run: NO
Frequency Capped:
   Now: NO
   Run: NO
Softlimit:
   Now: NO
   Run: NO

CPU temp=44.0'C
Redline=80'C

Messages since boot: 
1090mhz: 22,453
978mhz: 0
Tracks: 25

Installed SDR serials
(vendor code 0bda:*) 
978
1090

Position Count By Type: (info)
Last 1 Minute
Last 5 Minutes
Last 15 Minutes
Since Boot
 
{
  "adsb_icao": 841,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

{
  "adsb_icao": 4154,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

{
  "adsb_icao": 4154,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

{
  "adsb_icao": 4154,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

Current WiFi Status: 
wlan0     IEEE 802.11  ESSID:"lofgren"  
          Mode:Managed  Frequency:5.24 GHz  Access Point: 80:2A:A8:DB:72:53   
          Bit Rate=24 Mb/s   Tx-Power=31 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
          Link Quality=69/70  Signal level=-41 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Current IP Status: 
eth0: flags=4163  mtu 1500
        inet 192.168.1.155  netmask 255.255.255.0  broadcast 192.168.1.255
        ether b8:27:eb:91:f7:1e  txqueuelen 1000  (Ethernet)
        RX packets 20367  bytes 2241742 (2.1 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 18690  bytes 4955010 (4.7 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 54361  bytes 8640342 (8.2 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 54361  bytes 8640342 (8.2 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163  mtu 1500
        inet 192.168.1.200  netmask 255.255.255.0  broadcast 192.168.1.255
        ether b8:27:eb:c4:a2:4b  txqueuelen 1000  (Ethernet)
        RX packets 2007  bytes 686597 (670.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 18  bytes 1744 (1.7 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

IP Route: 
default via 192.168.1.1 dev eth0 proto dhcp src 192.168.1.155 metric 202 
default via 192.168.1.1 dev wlan0 proto dhcp src 192.168.1.200 metric 303 
192.168.1.0/24 dev eth0 proto dhcp scope link src 192.168.1.155 metric 202 
192.168.1.0/24 dev wlan0 proto dhcp scope link src 192.168.1.200 metric 303

readsb.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:27 UTC. --
May 11 04:26:19 adsbexchange systemd[1]: Started readsb ADS-B receiver.
May 11 04:26:19 adsbexchange readsb[513]: invoked by: /usr/bin/readsb --net-api-port 30152 --net-json-port 30154 --write-prom /run/readsb/stats.prom --gain -10 --lat 43.06299 --lon -77.27867 --device 1090 --device-type rtlsdr --ppm 0 --max-range 450 --heatmap-dir /var/globe_history --heatmap 30 --net --net-heartbeat 60 --net-ro-size 1200 --net-ro-interval 0.1 --net-ri-port 30001 --net-ro-port 30002 --net-sbs-port 30003 --net-bi-port 30004,30104 --net-bo-port 30005 --net-connector localhost,30006,json_out --net-connector localhost,30015,beast_reduce_out --net-beast-reduce-optimize-for-mlat --net-beast-reduce-interval=0.125 --net-connector feed.flyrealtraffic.com,30004,beast_reduce_plus_out,uuid=9c1097b9-4232-4042-8917-81704afd453d --json-location-accuracy 2 --range-outline-hours 8760 --write-state-only-on-exit --write-state=/var/globe_history --db-file /usr/local/share/tar1090/aircraft.csv.gz --write-json /run/readsb --quiet
May 11 04:26:19 adsbexchange readsb[513]: [2026-05-11 04:26:19.734 UTC] readsb starting up.
May 11 04:26:19 adsbexchange readsb[513]: readsb version: 3.16.10 wiedehopf git: 7d341c6 (committed: Sat Feb 28 18:32:06 2026 0100)
May 11 04:26:19 adsbexchange readsb[513]: Using lat: 43.062990, lon: -77.278670 (location accuracy: exact)
May 11 04:26:19 adsbexchange readsb[513]: loading state .....
May 11 04:26:22 adsbexchange readsb[513]: actual range outline, read bytes: 368644
May 11 04:26:22 adsbexchange readsb[513]:  .......... done, loaded 108 aircraft in 2.565 seconds!
May 11 04:26:22 adsbexchange readsb[513]: aircraft table fill: 0.0
May 11 04:26:22 adsbexchange readsb[513]: 30152: API output port
May 11 04:26:22 adsbexchange readsb[513]: 30002: Raw TCP output port
May 11 04:26:22 adsbexchange readsb[513]: 30005: Beast TCP output port
May 11 04:26:22 adsbexchange readsb[513]: 30154: Position json output port
May 11 04:26:22 adsbexchange readsb[513]: 30003: SBS TCP output ALL port
May 11 04:26:22 adsbexchange readsb[513]: 30001: Raw TCP input port
May 11 04:26:22 adsbexchange readsb[513]: 30004: Beast TCP input port
May 11 04:26:22 adsbexchange readsb[513]: 30104: Beast TCP input port
May 11 04:26:22 adsbexchange readsb[513]: BeastReduce TCP output: Name resolution for feed.flyrealtraffic.com failed: Temporary failure in name resolution
May 11 04:26:22 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (1): 111 (Connection refused)
May 11 04:26:22 adsbexchange readsb[513]: BeastReduce TCP output: Connection to localhost (127.0.0.1) port 30015 failed (1): 111 (Connection refused)
May 11 04:26:22 adsbexchange readsb[513]: rtlsdr: using device #1: Generic RTL2832U OEM (Realtek, RTL2838UHIDIR, SN 1090)
May 11 04:26:22 adsbexchange readsb[513]: BeastReduce TCP output: Name resolution for feed.flyrealtraffic.com failed: Temporary failure in name resolution
May 11 04:26:22 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (2): 111 (Connection refused)
May 11 04:26:22 adsbexchange readsb[513]: BeastReduce TCP output: Connection to localhost (127.0.0.1) port 30015 failed (2): 111 (Connection refused)
May 11 04:26:22 adsbexchange readsb[513]: Found Rafael Micro R820T tuner
May 11 04:26:23 adsbexchange readsb[513]: rtlsdr: tuner gain set to 59.0 dB (tuner AGC)
May 11 04:26:23 adsbexchange readsb[513]: Allocating 16 zero-copy buffers
May 11 04:26:23 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (3): 111 (Connection refused)
May 11 04:26:23 adsbexchange readsb[513]: BeastReduce TCP output: Connection to localhost (127.0.0.1) port 30015 failed (3): 111 (Connection refused)
May 11 04:26:23 adsbexchange readsb[513]: BeastReduce TCP output: Connection established: feed.flyrealtraffic.com (52.42.87.42) port 30004
May 11 04:26:24 adsbexchange readsb[513]: Database update in progress!
May 11 04:26:24 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (4): 111 (Connection refused)
May 11 04:26:24 adsbexchange readsb[513]: BeastReduce TCP output: Connection to localhost (127.0.0.1) port 30015 failed (4): 111 (Connection refused)
May 11 04:26:25 adsbexchange readsb[513]: Database update first part took 2.769 seconds!
May 11 04:26:25 adsbexchange readsb[513]: Database update done! (critical part took 0.001 seconds)
May 11 04:26:27 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (5): 111 (Connection refused)
May 11 04:26:27 adsbexchange readsb[513]: BeastReduce TCP output: Connection established: localhost (127.0.0.1) port 30015
May 11 04:26:31 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (6): 111 (Connection refused)
May 11 04:26:31 adsbexchange readsb[513]: Beast TCP output: Send Error: Broken pipe: 127.0.0.1 port 55566 (fd 45, SendQ 280, RecvQ 0)
May 11 04:26:31 adsbexchange readsb[513]: Beast TCP output: Send Error: Broken pipe: 127.0.0.1 port 55558 (fd 44, SendQ 280, RecvQ 0)
May 11 04:26:39 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (7): 111 (Connection refused)
May 11 04:26:54 adsbexchange readsb[513]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (8): 111 (Connection refused)
May 11 04:26:54 adsbexchange readsb[513]: [2026-05-11 04:26:54.581 UTC] Caught SIGTERM, shutting down...
May 11 04:26:54 adsbexchange systemd[1]: Stopping readsb ADS-B receiver...
May 11 04:27:07 adsbexchange readsb[513]: saving state .....
May 11 04:27:08 adsbexchange readsb[513]:  .......... done, saved 107 aircraft in 0.247 seconds!
May 11 04:27:08 adsbexchange readsb[513]: [2026-05-11 04:27:08.139 UTC] Normal exit. uptime:  0d  0h  0m 36.149s
May 11 04:27:08 adsbexchange systemd[1]: readsb.service: Succeeded.
May 11 04:27:08 adsbexchange systemd[1]: Stopped readsb ADS-B receiver.
May 11 04:27:08 adsbexchange systemd[1]: readsb.service: Consumed 6.636s CPU time.
May 11 04:27:08 adsbexchange systemd[1]: Started readsb ADS-B receiver.
May 11 04:27:08 adsbexchange readsb[1949]: invoked by: /usr/bin/readsb --net-api-port 30152 --net-json-port 30154 --write-prom /run/readsb/stats.prom --gain -10 --lat 43.06299 --lon -77.27867 --device 1090 --device-type rtlsdr --ppm 0 --max-range 450 --heatmap-dir /var/globe_history --heatmap 30 --net --net-heartbeat 60 --net-ro-size 1200 --net-ro-interval 0.1 --net-ri-port 30001 --net-ro-port 30002 --net-sbs-port 30003 --net-bi-port 30004,30104 --net-bo-port 30005 --net-connector localhost,30006,json_out --net-connector localhost,30015,beast_reduce_out --net-beast-reduce-optimize-for-mlat --net-beast-reduce-interval=0.125 --net-connector feed.flyrealtraffic.com,30004,beast_reduce_plus_out,uuid=9c1097b9-4232-4042-8917-81704afd453d --json-location-accuracy 2 --range-outline-hours 8760 --write-state-only-on-exit --write-state=/var/globe_history --db-file /usr/local/share/tar1090/aircraft.csv.gz --write-json /run/readsb --quiet
May 11 04:27:08 adsbexchange readsb[1949]: [2026-05-11 04:27:08.226 UTC] readsb starting up.
May 11 04:27:08 adsbexchange readsb[1949]: readsb version: 3.16.10 wiedehopf git: 7d341c6 (committed: Sat Feb 28 18:32:06 2026 0100)
May 11 04:27:08 adsbexchange readsb[1949]: Using lat: 43.062990, lon: -77.278670 (location accuracy: exact)
May 11 04:27:08 adsbexchange readsb[1949]: loading state .....
May 11 04:27:08 adsbexchange readsb[1949]: actual range outline, read bytes: 368644
May 11 04:27:08 adsbexchange readsb[1949]:  .......... done, loaded 107 aircraft in 0.026 seconds!
May 11 04:27:08 adsbexchange readsb[1949]: aircraft table fill: 0.0
May 11 04:27:08 adsbexchange readsb[1949]: 30002: Raw TCP output port
May 11 04:27:08 adsbexchange readsb[1949]: 30005: Beast TCP output port
May 11 04:27:08 adsbexchange readsb[1949]: 30154: Position json output port
May 11 04:27:08 adsbexchange readsb[1949]: 30003: SBS TCP output ALL port
May 11 04:27:08 adsbexchange readsb[1949]: 30152: API output port
May 11 04:27:08 adsbexchange readsb[1949]: 30001: Raw TCP input port
May 11 04:27:08 adsbexchange readsb[1949]: 30004: Beast TCP input port
May 11 04:27:08 adsbexchange readsb[1949]: 30104: Beast TCP input port
May 11 04:27:08 adsbexchange readsb[1949]: rtlsdr: using device #1: Generic RTL2832U OEM (Realtek, RTL2838UHIDIR, SN 1090)
May 11 04:27:08 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (1): 111 (Connection refused)
May 11 04:27:08 adsbexchange readsb[1949]: BeastReduce TCP output: Connection established: localhost (127.0.0.1) port 30015
May 11 04:27:08 adsbexchange readsb[1949]: BeastReduce TCP output: Connection established: feed.flyrealtraffic.com (52.42.87.42) port 30004
May 11 04:27:08 adsbexchange readsb[1949]: Found Rafael Micro R820T tuner
May 11 04:27:08 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (2): 111 (Connection refused)
May 11 04:27:08 adsbexchange readsb[1949]: rtlsdr: tuner gain set to 59.0 dB (tuner AGC)
May 11 04:27:08 adsbexchange readsb[1949]: Allocating 16 zero-copy buffers
May 11 04:27:09 adsbexchange readsb[1949]: Database update in progress!
May 11 04:27:09 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (3): 111 (Connection refused)
May 11 04:27:09 adsbexchange readsb[1949]: Database update first part took 1.036 seconds!
May 11 04:27:09 adsbexchange readsb[1949]: Database update done! (critical part took 0.001 seconds)
May 11 04:27:10 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (4): 111 (Connection refused)
May 11 04:27:12 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (5): 111 (Connection refused)
May 11 04:27:16 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (6): 111 (Connection refused)
May 11 04:27:24 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (7): 111 (Connection refused)
May 11 04:27:40 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (8): 111 (Connection refused)
May 11 04:27:55 adsbexchange readsb[1949]: Position json output: Connection to localhost (127.0.0.1) port 30006 failed (9): 111 (Connection refused)
May 11 04:28:11 adsbexchange readsb[1949]: Position json output: Connection to localhost port 30006 failed 10 times, suppressing most error messages until connection succeeds

dump978-fa.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:28 UTC. --
May 11 04:26:19 adsbexchange systemd[1]: Started dump978 ADS-B UAT receiver.
May 11 04:26:20 adsbexchange dump978-fa[511]: raw-port: listening for connections on 0.0.0.0:30978
May 11 04:26:20 adsbexchange dump978-fa[511]: raw-port: listening for connections on [::]:30978
May 11 04:26:20 adsbexchange dump978-fa[511]: json-port: listening for connections on 0.0.0.0:30979
May 11 04:26:20 adsbexchange dump978-fa[511]: json-port: listening for connections on [::]:30979
May 11 04:26:21 adsbexchange dump978-fa[511]: Found Rafael Micro R820T tuner
May 11 04:26:22 adsbexchange dump978-fa[511]: Found Rafael Micro R820T tuner
May 11 04:26:22 adsbexchange dump978-fa[511]: Found Rafael Micro R820T tuner
May 11 04:26:22 adsbexchange dump978-fa[511]: Exact sample rate is: 2083333.135571 Hz
May 11 04:26:23 adsbexchange dump978-fa[511]: [R82XX] PLL not locked!
May 11 04:26:23 adsbexchange dump978-fa[511]: SoapySDR: using manual gain 48.0 dB
May 11 04:26:23 adsbexchange dump978-fa[511]: SoapySDR: using stream setting buffsize=262144
May 11 04:26:23 adsbexchange dump978-fa[511]: Allocating 15 zero-copy buffers
May 11 04:26:23 adsbexchange dump978-fa[511]: 0.0.0.0:30978: accepted a connection from 127.0.0.1:52574
May 11 04:26:23 adsbexchange dump978-fa[511]: 0.0.0.0:30978: accepted a connection from 127.0.0.1:52588
May 11 04:26:23 adsbexchange dump978-fa[511]: 0.0.0.0:30978: accepted a connection from 127.0.0.1:52602
May 11 04:26:23 adsbexchange dump978-fa[511]: 0.0.0.0:30978: accepted a connection from 127.0.0.1:52614

autogain1090.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:28 UTC. --
-- No entries --

tar1090.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:28 UTC. --
May 11 04:26:20 adsbexchange systemd[1]: Started tar1090 - compress dump1090 json data.

tar1090-978.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:28 UTC. --
May 11 04:26:20 adsbexchange systemd[1]: Started tar1090-978 - compress dump1090 json data.

adsbexchange-feed.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:28 UTC. --
May 11 04:26:19 adsbexchange systemd[1]: Started adsbexchange-feed.
May 11 04:26:19 adsbexchange adsbexchange-feed[535]: Mon May 11 04:26:19 2026 UTC  readsb starting up.
May 11 04:26:19 adsbexchange adsbexchange-feed[535]: readsb version: wiedehopf git: d809bd8 (committed: Wed Sep 7 13:47:41 2022 0200)
May 11 04:26:19 adsbexchange adsbexchange-feed[535]: Using lat:   43.0630, lon:  -77.2787
May 11 04:26:19 adsbexchange adsbexchange-feed[535]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 11 04:26:20 adsbexchange adsbexchange-feed[535]: BeastReduce TCP output: Name resolution for feed1.adsbexchange.com failed: Temporary failure in name resolution
May 11 04:26:20 adsbexchange adsbexchange-feed[535]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 11 04:26:20 adsbexchange adsbexchange-feed[535]: BeastReduce TCP output: Name resolution for feed2.adsbexchange.com failed: Temporary failure in name resolution
May 11 04:26:21 adsbexchange adsbexchange-feed[535]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 11 04:26:21 adsbexchange adsbexchange-feed[535]: BeastReduce TCP output: Name resolution for feed1.adsbexchange.com failed: Temporary failure in name resolution
May 11 04:26:23 adsbexchange adsbexchange-feed[535]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 11 04:26:23 adsbexchange adsbexchange-feed[535]: BeastReduce TCP output: Connection established: feed2.adsbexchange.com (34.218.254.209) port 64004
May 11 04:27:07 adsbexchange adsbexchange-feed[535]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 6, SendQ 0, RecvQ 0)
May 11 04:27:07 adsbexchange adsbexchange-feed[535]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 11 04:27:08 adsbexchange adsbexchange-feed[535]: Beast TCP input: Connection established: 127.0.0.1 port 30005

adsbexchange-mlat.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:28 UTC. --
May 11 04:26:19 adsbexchange systemd[1]: Started adsbexchange-mlat.
May 11 04:26:23 adsbexchange adsbexchange-mlat[533]: mlat-client 0.4.2 starting up
May 11 04:26:23 adsbexchange adsbexchange-mlat[533]: Listening for Basestation-format results connection on port 31003
May 11 04:26:23 adsbexchange adsbexchange-mlat[533]: Listening for Beast-format results connection on port 30157
May 11 04:26:23 adsbexchange adsbexchange-mlat[533]: Connected to multilateration server at feed2.adsbexchange.com:64590, handshaking
May 11 04:26:24 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection established
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]: Server says:
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]:         
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]:         The multilateration server source code is available under
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]:         the terms of the Affero GPL (v3 or later). You may obtain
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]:         a copy of this server's source code at the following
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]:         location: https://github.com/adsbexchange/mlat-server
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]:         
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]: Handshake complete: Compression zlib2, UDP transport disabled, Split sync disabled
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]: Input connected to 127.0.0.1:30005
May 11 04:26:28 adsbexchange adsbexchange-mlat[533]: Input format changed to BEAST, 12MHz clock
May 11 04:27:07 adsbexchange adsbexchange-mlat[533]: Lost connection to 127.0.0.1:30005
May 11 04:27:07 adsbexchange adsbexchange-mlat[533]: Reconnecting in 2.9 seconds
May 11 04:27:07 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection lost
May 11 04:27:11 adsbexchange adsbexchange-mlat[533]: Input connected to 127.0.0.1:30005
May 11 04:27:11 adsbexchange adsbexchange-mlat[533]: Input format changed to BEAST, 12MHz clock
May 11 04:27:35 adsbexchange adsbexchange-mlat[533]: Receiver: connected    69.2 msg/s received       35.1 msg/s processed (51%)
May 11 04:27:35 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.2 kB/s to server
May 11 04:27:35 adsbexchange adsbexchange-mlat[533]: Results:  0.0 positions/minute
May 11 04:27:35 adsbexchange adsbexchange-mlat[533]: Aircraft: 0 of 5 Mode S, 8 of 10 ADS-B used
May 11 04:27:37 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection established
May 11 04:27:44 adsbexchange adsbexchange-mlat[533]: peer_count:  72 outlier_percent: 0.0 bad_sync_timeout:   0

adsbexchange-stats.service logs: 
-- Journal begins at Mon 2026-05-11 04:26:14 UTC, ends at Mon 2026-05-11 04:31:28 UTC. --
May 11 04:26:18 adsbexchange systemd[1]: Started ADSBexchange Stats.
May 11 04:26:23 adsbexchange adsbexchange-stats[416]: Note: 'USE_OLD_PATH' is set.
May 11 04:26:24 adsbexchange adsbexchange-stats[416]: Using UUID [xxxx-xxx-xxx-6e809370ffd6] for stats uploads
May 11 04:26:24 adsbexchange adsbexchange-stats[416]: Using JSON directory [/run/readsb] for source data
May 11 04:26:24 adsbexchange adsbexchange-stats[416]: Using script's DNS cache (600 seconds)

/boot/adsbx-env 
# Default no serial single SDR mode
# use # to comment out for 1090 mode
RECEIVER_OPTIONS="--device 1090 --device-type rtlsdr --ppm 0"

# 1090 serialed SDR
# Remove # for 1090 serial mode
#RECEIVER_OPTIONS="--device 1090 --device-type rtlsdr --ppm 0"

DECODER_OPTIONS="--max-range 450 --heatmap-dir /var/globe_history --heatmap 30"
NET_OPTIONS="--net --net-heartbeat 60 --net-ro-size 1200 --net-ro-interval 0.1 \
        --net-ri-port 30001 --net-ro-port 30002 --net-sbs-port 30003 \
        --net-bi-port 30004,30104 --net-bo-port 30005 --net-connector localhost,30006,json_out \
	--net-connector localhost,30015,beast_reduce_out --net-beast-reduce-optimize-for-mlat --net-beast-reduce-interval=0.125 \
	--net-connector feed.flyrealtraffic.com,30004,beast_reduce_plus_out,uuid=9c1097b9-4232-4042-8917-81704afd453d"
JSON_OPTIONS="--json-location-accuracy 2 --db-file /usr/local/share/tar1090/aircraft.csv.gz"

# uncomment (remove #) the following line to make the actual range outline persist reboots
JSON_OPTIONS="--json-location-accuracy 2 --range-outline-hours 8760 --write-state-only-on-exit --write-state=/var/globe_history --db-file /usr/local/share/tar1090/aircraft.csv.gz"

INPUT="127.0.0.1:30005"
RESULTS="--results beast,connect,localhost:30104 --results basestation,listen,31003 --results beast,listen,30157"
MLATSERVER="feed.adsbexchange.com:31090"
INPUT_TYPE="dump1090"
#INPUT_TYPE="dump1090 --privacy"
SERVERPORT="30005"
#this new comment is in adsbx-env

/boot/adsbx-978env 
RECEIVER_978_OPTIONS="--net-only"
DECODER_978_OPTIONS="--max-range 460"
NET_978_OPTIONS="--net --net-heartbeat 60 --net-ro-interval 0.5 --net-ro-port 0 --net-sbs-port 0 --net-bi-port 0 --net-bo-port 0 --net-connector localhost,30004,beast_out"
JSON_978_OPTIONS="--json-location-accuracy 2"

ENABLED=yes
#RECEIVER_OPTIONS="--sdr-gain 36.4 --sdr driver=rtlsdr,serial=978 --format CS8"
RECEIVER_OPTIONS="--sdr-gain 48 --sdr driver=rtlsdr,serial=978 --format CS8"
DECODER_OPTIONS=""
NET_OPTIONS="--raw-port 30978 --json-port 30979"

Log for last update